Vidir Wire Spool Carousel Case Study: IES Residential, McKinney, Texas

How a residential electrical contractor put 39 wire bays of building wire into one 19-foot Vidir Wire Spool Carousel with measured payout at the pick opening.

Tall Vidir wire spool carousel loaded with residential building wire spools in a distribution warehouse

Customer

IES Residential

Location

711 Tower Lane, McKinney, TX 75069 (Collin County)

Product

Vidir Wire Carousel, Model W39225-1334-06 — 13 carriers, 39 wire bays

Application

Motorized storage and measured payout of residential building wire spools

About the project

IES Residential is a residential electrical contractor — the kind of operation that wires whole subdivisions, runs a fleet of vans out of one building every morning, and buys building wire by the spool in a handful of gauges but very large quantities. Its facility at 711 Tower Lane in McKinney, Texas, north of Dallas in Collin County, is where that wire is held and staged.

Material Handling USA supplied and installed one Vidir Wire Carousel — a motorized vertical carousel whose carriers are enclosed wire bays, Model W39225-1334-06 — at the McKinney facility. The machine stands 19’3" high on an 8’9" by 6’3" footprint, carries thirteen carriers with 39 individual wire bays, and was ordered with three payout accessories: a certified wire meter slider, a wire spinner spool assembly and a wire spool lift-and-load dolly.

That accessory package is what makes this project worth studying. A residential contractor does not just store wire, it issues measured lengths to crews all day — and the meter slider is how that stops being a guess. The install is one of the projects behind our vertical storage for electrical supply and wire distribution page and part of the Vidir vertical storage line.

Project scope at a glance

■

Vidir Wire Carousel W39225-1334-06

A powered vertical carousel 19’3″ high on an 8’9″ wide by 6’3″ deep footprint, built specifically for spooled building wire.

▲

13 carriers, 39 wire bays

Thirteen W39 wire-bay carriers give 39 individual bays, each 26.25″ wide by 26.5″ high, for spools up to 24″ in diameter.

●

13,000 lb machine capacity

Rated for 13,000 lbs overall with an 11,861 lb live load, up to 1,000 lbs on any single carrier and a 912 lb average across all thirteen.

📏

Certified wire meter slider

An imperial certified meter slider measures wire as it is pulled at the opening, so a crew leaves with a known length instead of an estimate.

🔄

Wire spinner spool

A rotating spinner spool assembly lets cable pay out under even tension instead of dragging over a fixed rod.

🚚

Wire spool lift and load

A lift-and-load dolly for getting full spools up to bay height without manhandling them.

The situation

Residential electrical work runs on a short list of wire types in enormous volume. That sounds easy to store until you count spools: several gauges, multiple jacket types and colors, ground wire, and enough of each to keep crews from running dry mid-week. Stored on static reel racks, that inventory takes a long wall plus the aisle in front of it, in a building where floor space is already committed to staging, material carts and van bays.

The bigger cost is the daily handling. Every crew that leaves needs a length of wire, and on a rack that means finding the right spool, getting a stand under it, spinning it by hand, guessing the length or measuring it across the floor afterwards, and lifting the partial spool back onto a pin. Multiply that by a fleet of vans leaving each morning and the wasted time is real — as is the over-pull that quietly inflates wire cost per house.

A wire carousel with measured payout changes the whole transaction. The operator calls the carrier, the machine rotates that bay to one fixed opening at working height, and the wire is measured as it comes off the spool without the spool ever leaving the machine.

Vidir wire carousel hanger meter slider measuring wire at the pick opening

What Material Handling USA supplied

Material Handling USA supplied and installed one Vidir Wire Carousel, Model W39225-1334-06: a freestanding powered carousel 19’3" high, 8’9" wide and 6’3" deep, with thirteen W39 wire-bay carriers, uprights with a 2" wire mesh front and a corrugated sheet metal back, and a front control tower.

Each carrier is divided into three wire bays — 39 bays in total — measuring 26.25" wide by 26.5" high, sized for spools up to 24" in diameter. Spools mount on wire bay rods, and the machine shipped with twenty-six 0.75" standard-duty rods and forty-four 1" heavy-duty rods, so bays can be re-cut for different spool widths as the stocked wire list changes.

Two 1.5 HP Leeson motors drive the carousel at a fixed speed, moving carriers at up to 21 feet per minute. Controls are forward/reverse push buttons at the front control tower, with a mushroom E-stop, a main power disconnect and a security keypad — the keypad matters in a building where a lot of people walk past a lot of copper. Power is 208V, three-phase, 15 amp on an isolated circuit, hooked up at the front top right corner of the machine. The tower is anchored to the slab with 5/8" HILTI KB-TZ stud anchors through 9.5" x 6" foot plates.

Three accessories were ordered with the machine. The imperial certified wire meter slider measures wire as it is drawn off at the opening. The wire spinner spool assembly rotates in its bay so cable unwinds under even tension. The wire spool lift-and-load dolly raises full spools to bay height for loading. All three are cataloged on our vertical carousel accessories and options page.

Full product specifications

Below is the published product specification for the machine installed at the McKinney facility. A carousel is a manufactured product, so these are the numbers used to confirm it would clear the ceiling, fit the space and carry the spool weights.

Specification Value
Model W39225-1334-06
Product type Wire Carousel (vertical carousel)
Overall height 19′ 3″
Overall width 8′ 9″
Overall depth 6′ 3″
Overall weight capacity 13,000 lbs
Live load capacity 11,861 lbs
Carrier type W39 wire bay
Total carriers 13
Total wire bays 39
Wire bay dimensions 26.25″ W x 26.5″ H
Maximum spool diameter 24″
Maximum weight per carrier 1,000 lbs
Average capacity per carrier 912 lbs
Standard-duty wire bay rods (26) 0.75″ rods
Heavy-duty wire bay rods (44) 1″ rods
Drive system (2) 1.5 HP Leeson motors
Electrical 208V, 3-phase, 15 amp (isolated circuit)
Controls Forward/reverse push button, front control tower
Drive configuration Fixed speed
Control options Mushroom E-stop, main power disconnect, security keypad
Max. retrieval speed 21 ft per minute
Guarding Uprights, 2″ wire mesh front, corrugated sheet metal back
Foot plate dimensions 9.5″ D x 6″ W x 0.375″ H
Concrete anchors 5/8″ HILTI KB-TZ stud anchor
Finish VM White Textured (300-1106), machine and carriers
Options supplied on this project Imperial certified wire meter slider, wire spinner spool assembly, wire spool lift and load
Warranty 2 years parts and labor (manufacturer)
Vidir wire carousel spinner spool assembly for even-tension cable payout

Install and site requirements

The manufacturer’s order acknowledgement for this project spells out exactly what a site has to have ready, and it is worth publishing because it is the same list on every wire carousel we install.

Electrical: 208 volt, three phase, 15 amp on an isolated circuit per machine, roughed in by the site electrician in advance. An electrician has to be available part-way through installation for final hookup, because the connection point is on the front top right corner of the machine once the tower is standing.

Forklift: one 3,000–4,000 lb capacity forklift with 4 ft forks and at least 15 ft of high reach, available for unloading and erection.

Scissor lift: one 18–20 ft electric scissor lift with a maximum 32" base width — the narrow base matters because the lift has to work close to the tower.

Vidir’s installers are certified to operate forklifts and scissor lifts themselves; where site rules do not allow that, the site provides an operator for the duration. The floor has to be level and troweled smooth, at least 6" thick, so 5/8" stud anchors can hold the column loads. Our vertical storage installation services page carries the full pre-install checklist.

Vidir wire carousel wire spool lift and load dolly option

What the contractor gained

↑

39 bays in one footprint

Thirty-nine wire bays stack to 19’3″ inside one 8’9″ x 6’3″ footprint instead of running reel racks down a wall.

📏

Measured issue, not estimated

The certified meter slider means every length leaving the building is a known number — which is how over-pull and wire cost per job get controlled.

⏱

Faster morning staging

The requested carrier rotates to a fixed opening at up to 21 feet per minute, so crews are not waiting on someone to find a spool.

⚖

Safer spool handling

The lift-and-load dolly puts full spools into bays without manhandling, and spools stay on their rods for every pull afterwards.

🔒

Copper behind a keypad

An enclosed mesh tower with a security keypad on the control tower keeps high-value wire inside a machine, not on an open rack.

🔧

Reconfigurable bays

Seventy bay rods in two diameters, plus spinner spools, let the bay layout follow the stocked wire list without changing the machine.

Wire carousel or static reel rack?

Vidir Wire Carousel (used here) Static wire reel rack
Floor footprint One 8’9″ x 6’3″ footprint Runs along a wall plus a clear working aisle
Vertical use Stores to 19’3″ and picks at one opening Limited to safe manual reach
Bay count 39 bays at 26.25″ x 26.5″ As many positions as wall length allows
Spool handling Spools stay on rods inside the machine Manual lift on and off the rack
Payout Certified meter slider and spinner spool at the opening Reel stand, then measure by hand
Access control Enclosed mesh, keypad on the control tower Open rack
Best for High-volume issuing from a short list of gauges A handful of spools and low turnover

Our wire spool carousel vs. wire reel rack comparison covers the economics, and the vertical carousel vs. traditional storage page applies the same logic to parts and supplies. For high-throughput distribution operations, the vertical storage for warehousing and logistics page covers the wider picking case.

How to specify a wire carousel

Start with the wire, not the machine. List every spool type you stock, the largest spool diameter and width, and the weight of a full spool. Those numbers set the bay size, the rod diameter and the carrier rating — here, 26.25" x 26.5" bays, spools to 24" diameter, 1,000 lbs per carrier and a mix of 0.75" and 1" rods.

Then measure the building, because the building picks the model. This platform is built in several heights on the same 8’9" x 6’3" footprint: seven carriers at 10’9" for a low-clearance warehouse, thirteen carriers at 19’3" as installed here, and W45 machines that reach 21 feet with larger bays. Confirm clear height under sprinklers and lights before anything else.

Decide the payout hardware up front. Meter sliders, spinner spools and lift-and-load dollies all mount to the same machine, but adding them later is a second freight bill. If you issue measured lengths daily, the meter slider is the accessory that pays for itself.

Compare projects before you size yours: the 7-carrier machine at an electrical contractor in Englewood, Colorado for a low-ceiling building, the 21-foot, 36-bay wire reel carousel at Tucson Electric Power for utility reels, the cable drum carousel at an electrical wholesaler for large drums, and the compact machine in a maintenance stores for a small wire list. For taller or highly variable loads compare a vertical lift module, for budget ranges start with the vertical storage cost and pricing guide, and machine details for this platform live on the Vidir Wire Carousel page. We supply and install nationwide, including the Dallas–Fort Worth metroplex.

Front view of Vidir wire carousel wire bay carriers loaded with wire spools

Frequently asked questions

What is a wire spool carousel?
It is a powered vertical carousel whose carriers are enclosed wire bays. Spools mount on steel rods inside the bays, the carriers rotate vertically inside a guarded tower, and wire is paid out at one fixed opening at working height. The machine installed here is a Vidir W39225-1334-06.
How many wire spools does this machine hold?
Thirteen carriers with three bays each — 39 wire bays measuring 26.25″ wide by 26.5″ high — for spools up to 24″ in diameter, rated at 1,000 lbs per carrier and 13,000 lbs overall.
How much floor space does it use?
One footprint 8’9″ wide by 6’3″ deep, plus clear space at the pick opening. All of the capacity above that is vertical — the machine is 19’3″ high.
Can wire be measured as it comes off the spool?
Yes. An imperial certified wire meter slider was supplied with this machine, so wire is measured at the pick opening as it is drawn off. That is how contractors control over-pull and wire cost per job.
What is a wire spool lift and load?
A dolly that lifts a full spool to bay height so it can be loaded into a carrier without being manhandled. One was supplied on this project along with a spinner spool assembly.
What power does a wire carousel need?
This model runs on 208V, three-phase, 15 amp power on an isolated circuit, with a main power disconnect, a mushroom E-stop and a security keypad at the front control tower. The hookup point is the front top right corner of the machine.
What does the site have to provide for installation?
Wiring roughed in ahead of the crew and an electrician for final hookup mid-install, one 3,000-4,000 lb forklift with 4 ft forks and 15 ft reach, one 18-20 ft electric scissor lift with a maximum 32″ base width, and a level troweled slab at least 6″ thick for 5/8″ HILTI KB-TZ stud anchors.
Do you supply wire carousels to electrical contractors in Texas?
Yes. We supply and install wire carousels, vertical carousels and storeroom systems for residential and commercial electrical contractors, wholesalers and utilities nationwide, including McKinney and the Dallas-Fort Worth metroplex.

Issuing measured wire out of a reel rack?

Send us your spool list — gauges, largest spool diameter and full-spool weights — plus your clear ceiling height, and we will size a Vidir Wire Carousel with the bay layout, meter slider and installation scope your operation needs.

Headquartered in Salt Lake City, UT • Serving customers nationwide
Local service areas: Salt Lake City • Provo • Ogden • Park City • St. George • Logan • Lehi • Orem