Wire Spool Carousel for an Electrical Supply House: CES El Cajon, California

How a San Diego County electrical distributor branch put 21 bays of spooled wire, on spools up to 30 inches, into one 12’6″ Vidir Wire Carousel built with heavy-duty rods in every bay.

Vidir W45 wire spool carousel with mesh guard and loaded wire bays in an electrical supply distributor warehouse

21

Wire bays on 7 carriers

30 in

Maximum spool diameter

12’6″

Overall machine height

63

Heavy-duty 1 in bay rods

About the Project

California Electric Supply, known locally as CES El Cajon, is an electrical supply house at 1080 North Johnson Avenue in El Cajon, California, in east San Diego County. The branch operates as a division of Consolidated Electrical Distributors (CED), one of the largest electrical distributors in the country, while keeping its own local name and inventory for Southern California contractors. Its counter opens at 6 AM on weekdays, it runs jobsite delivery across the region, and it publicly lists THHN building wire up to 500 MCM and conduit up to 4 inches among the commodities it keeps in stock.

Material Handling USA supplied one Vidir Wire Carousel, Model W45143-0740-06, to the El Cajon branch, with freight, inside delivery and installation included in the order. The machine is a motorized vertical carousel whose carriers are enclosed wire bays: seven carriers, 21 bays, spools up to 30 inches in diameter, all in a footprint 8’9″ wide by 7’3″ deep and 12’6″ tall.

Vidir Wire Carousel installed at an electrical distributor with loaded wire bays

Wire is the inventory that defines an electrical distributor. It is heavy, it is sold by the foot, it turns over every day, and the spools never shrink to a convenient size. This project is one of the real installations behind our vertical storage for electrical supply and wire distribution page, and part of the wider Vidir vertical storage solutions line we supply and install nationwide.

Project Scope at a Glance

■

Vidir W45143-0740-06

A powered wire carousel 12’6″ high on an 8’9″ by 7’3″ footprint, built for spooled wire and cable.

▲

7 carriers, 21 wire bays

Seven W45 wire-bay carriers, three bays each, every bay 26.25″ wide by 32.5″ high.

●

Spools up to 30 in

The W45 bay takes spools up to 30 inches in diameter, larger than the 24 inch limit of the W39 platform.

🔩

Heavy-duty rods throughout

The order specified 1 inch heavy-duty wire bay rods for every position, 63 in total, including extra rods.

⚖

13,000 lb rated machine

13,000 lbs overall capacity, a 12,315 lb live load and up to 1,000 lbs on any one carrier.

🚚

Delivered and installed

Freight, inside delivery and installation by certified Vidir installers were part of the order.

Shop Static Wire Spool Racks Online

The Vidir Wire Carousel is quoted to order, not sold from the online store. For overflow spools, a contractor counter or a smaller stockroom, these real wire spool racks, portable spool racks, reel holders and reel rods ship from our catalog.

The Situation: Wire at a Busy Distributor Branch

Spools of copper building wire on floor-level reel stands below conduit racks in an electrical supply house warehouse

An electrical supply branch lives on wire sales. Contractors call in or walk up for a cut length of a given gauge and color, and the counter has to find the spool, pay out the wire, cut it and get the spool back into place, often for several orders at once before crews head to the jobsite. The usual way of holding that stock is spools on floor-level reel stands and static spool racks along a warehouse wall.

That works until the wire list grows. Each new gauge, color or jacket type adds another spool, each spool needs its own stand or rack position, and the run of stands gets longer and lower. The heaviest spools end up on the floor, staff bend and lift to reach them, and the floor space in front of the stands has to stay clear for access. In a branch that also stocks conduit, panels, fittings and lighting, that floor space is worth more as storage for everything else.

A wire carousel solves the space side and the handling side at once: spools stack vertically inside one guarded machine, and the bay that holds the wire you need rotates down to a fixed opening at working height. Our guides on the wire carousel for electrical wholesalers and on wire reel storage systems for electrical supply warehouses cover the general case in more depth.

What Material Handling USA Supplied

The El Cajon branch received one freestanding Vidir Wire Carousel, Model W45143-0740-06. It stands 12’6″ high, 8’9″ wide and 7’3″ deep, with uprights and a 2 inch wire mesh guard front and back, a front control tower, and seven W45 wire-bay carriers. Each carrier is divided into three bays, for 21 bays in total, and each bay measures 26.25 inches wide by 32.5 inches high.

Two 1.5 HP Leeson motors drive the carousel at a fixed speed, moving carriers at up to 21 feet per minute. The operator uses forward and reverse push buttons at the front control tower, with a mushroom emergency stop and a main power disconnect. The machine runs on 208 volt, three phase, 15 amp power on an isolated circuit and is anchored to the slab with 5/8 inch HILTI KB-TZ stud anchors through 9.5 by 6 inch foot plates.

Vidir Wire Carousel loaded with cable spools behind its wire mesh guard

What sets this order apart from the other distributor and contractor machines we have installed is the rod package. Vidir’s standard configuration mixes 0.75 inch standard-duty rods with 1 inch heavy-duty rods. For this branch the order called for 1 inch heavy-duty rods in every position: the specification sheet lists zero standard-duty rods and 63 heavy-duty rods, and our purchase order to Vidir added extra 1 inch rods on top of the standard set so the bays could be divided for the branch’s spool widths from day one.

Why a W45 Wire Carousel Instead of a W39

Vidir builds its wire carousels on two carrier platforms. The difference is the bay, and the bay is set by the largest spool you stock. Contractors who buy a short list of building wire on smaller spools often fit the W39 platform; distributors who sell larger spools and heavier conductors need the taller W45 bay. Both platforms come in several heights, so the ceiling picks the carrier count once the bay is chosen.

W45 platform (used here) W39 platform
Wire bay size 26.25″ W x 32.5″ H 26.25″ W x 26.5″ H
Maximum spool diameter 30 in 24 in
Footprint depth 7’3″ 6’3″
Footprint width 8’9″ 8’9″
Bays per carrier 3 3
Example installs CES El Cajon (7 carriers), Tucson Electric Power (12), ABL Space Systems (8) Duro Electric (7 carriers), IES Residential (13)

The El Cajon machine is the shortest W45 configuration we have documented in a case study. Seven carriers at 12’6″ keep the tower well under typical warehouse clear heights while still giving every bay the full 30 inch spool capacity. Compare the 12-carrier W45 machine at Tucson Electric Power, which stands over 21 feet for utility reels, and the 7-carrier W39 machine at an electrical contractor in Englewood, Colorado, which shares this carrier count but uses the smaller bay.

Vidir drawing of the W45143-0740-06 wire carousel showing front and side views with overall dimensions
Vidir drawing for model W45143-0740-06: front and side views with overall width, depth and height in inches and millimeters. Rated 13,000 lbs overall and 1,000 lbs per carrier.

Full Product Specifications

These are the figures from Vidir’s product specification sheet for the machine supplied to El Cajon, cross-checked against Vidir’s drawing for the same model. A wire carousel is a manufactured product, so these are the numbers used to confirm it fits the space, clears the ceiling and carries the spool weights.

Specification Value
Model W45143-0740-06
Product type Wire Carousel (vertical carousel)
Overall height 12′ 6″
Overall width 8′ 9″
Overall depth 7′ 3″
Overall weight capacity 13,000 lbs
Live load capacity 12,315 lbs
Carrier type W45 wire bay
Total carriers 7
Total wire bays 21
Wire bay dimensions 26.25″ W x 32.5″ H
Maximum spool diameter 30″
Maximum weight per carrier 1,000 lbs
Average capacity per carrier 1,000 lbs
Standard-duty wire bay rods None (0.75″ rods not used)
Heavy-duty wire bay rods (63) 1″ rods
Drive system (2) 1.5 HP Leeson motors
Electrical 208V, 3-phase, 15 amp (isolated circuit)
Controls Forward/reverse push button
Drive configuration Fixed speed
Control options Mushroom E-stop, main power disconnect
Control location Front, control tower
Max. retrieval speed 21 ft per minute
Guarding Uprights, 2″ wire mesh front and back
Foot plate dimensions 9.5″ D x 6″ W x 0.375″ H
Concrete anchors 5/8″ HILTI KB-TZ stud anchor
Finish VM White Textured
Scope of order Machine, extra 1″ rods, freight, inside delivery and installation
Front view of a Vidir Wire Carousel showing wire bay carriers and spools on rods

Why the rods matter. In a wire carousel the spool sits on a steel rod that spans the bay, and the rod is what carries the spool’s weight into the carrier. A 1 inch rod is stiffer than a 0.75 inch rod over the same span, which is why heavy-duty rods are the usual choice for full spools of larger conductors. Rods are also how bays are divided: more rods let the branch split a 26.25 inch bay into narrower positions for smaller spools, or open it up for one wide spool.

Ordering extra rods with the machine is cheap insurance. Wire lists change with the projects contractors are bidding, and having spare rods on hand means the bay layout can follow the stock without waiting on a parts order. Replacement rods and other parts for existing machines are covered on our Vidir parts and service support page.

Installation and Site Requirements

Vidir’s customer order acknowledgement for this project lists what the site needed ready before the installers arrived. It is the same short list we review with every wire carousel buyer, so it is worth publishing in full:

  • Power: 208 volt, three phase, 15 amp on an isolated circuit for the machine, roughed in by the site electrician ahead of installation.
  • Electrician mid-install: an electrician returns part-way through for final hookup. The outlet location is the front, top right corner of the machine when facing it.
  • Forklift: one 5,000 lb capacity forklift with 6 ft forks and at least 12 ft of high reach, for unloading the machine, moving components and assembly.
  • Scissor lift: one 18 to 20 ft electric scissor lift with a base no wider than 32 inches, so it can work close to the tower.
  • Certified operators: Vidir’s installers are certified on forklifts and scissor lifts and prefer to run them; if site rules do not allow that, the site provides an operator for the duration.
  • Slab: a sound, level concrete floor that will hold 5/8 inch HILTI KB-TZ stud anchors at each foot plate.
1

Confirm the spool list

Largest spool diameter and width, full-spool weights and the number of positions needed set the platform and rod package.

2

Size to the building

Clear height under sprinklers and lights picks the carrier count; the 8’9″ x 7’3″ footprint plus a clear pick zone is laid out on the floor plan.

3

Prepare the site

The electrician runs the isolated 208V circuit and the lift equipment is lined up for install day.

4

Deliver and install

The machine is delivered inside, erected, anchored, hooked up and tested, then staff are shown loading and rotation.

The full pre-install checklist we use, including slab and access questions, is on our vertical storage installation services page.

What the Branch Gained

↑

21 bays in one footprint

Twenty-one wire bays stack to 12’6″ inside an 8’9″ by 7’3″ footprint instead of a long run of floor stands.

⏱

Wire comes to the operator

The bay you call rotates to one fixed opening at up to 21 feet per minute, so nobody searches a wall of spools.

⚖

Less lifting and bending

Spools stay on their rods inside the machine for every pull. Staff work at the opening rather than bending to floor-level stands.

◉

Room for large spools

W45 bays take spools up to 30 inches across, so larger conductor sizes fit alongside common building wire.

🔩

A rod package built for weight

Heavy-duty 1 inch rods in every position carry full spools and leave room to rearrange the bays.

🔒

Guarded, enclosed stock

The 2 inch wire mesh guard front and back keeps copper inside a machine rather than on open racks.

Payout options for later. This order was the machine, rods, freight and installation, with no payout accessories. That is a common way to start: Vidir’s accessories mount to the same carousel, so a branch can add them when counter volume justifies it.

The ones distributors ask about most are a hanger meter slider that measures wire at the opening as it is drawn off, a wire spinner spool that lets cable pay out under even tension, and a wire loading dolly for raising full spools to bay height. All three are described on our vertical carousel accessories and options page, and the IES Residential case study shows a machine ordered with the full set.

Vidir wire carousel hanger meter slider and payout dolly at the pick opening

How This Install Compares to Other Wire Projects

Electrical distributors, contractors and utilities buy wire carousels for different reasons, and the right machine follows the spool list. These are the electrical-sector Vidir projects we have documented:

Project Customer type Machine What drove the choice
World Electric Supply, Hialeah Gardens FL Electrical wholesaler Two tire-carousel platform machines Large cable drums, not spools
CES El Cajon, El Cajon CA (this page) Electrical distributor branch W45, 7 carriers, 21 bays, 12’6″ 30 inch spools, heavy-duty rods throughout
Duro Electric, Englewood CO Electrical contractor W39, 7 carriers, 21 bays, 10’9″ Low ceiling, 24 inch spools
IES Residential, McKinney TX Residential electrical contractor W39, 13 carriers, 39 bays, 19’3″ High-volume issuing with meter slider
Tucson Electric Power, Tucson AZ Electric utility W45, 12 carriers, 36 bays, 21’1″ Utility reels, maximum bay count

For a static alternative and the economics of each, read our wire spool carousel vs. wire reel rack comparison and the vertical carousel vs. traditional storage page. Every wire application we serve, from distributors to aerospace wire rooms, is mapped on the motorized wire spool carousel page, and drum-sized cable has its own motorized wire and cable reel carousel page. Another Southern California example is the W45 wire carousel at ABL Space Systems in El Segundo.

How to Specify a Wire Carousel for Your Branch

Start with the wire, not the machine. List every spool you stock or plan to stock with its diameter, width and full weight. The largest diameter picks the platform: up to 24 inches fits W39 bays, up to 30 inches needs W45. Full-spool weights tell you whether heavy-duty rods belong in every position, as they do here, and confirm that no carrier will exceed its 1,000 lb rating.

  • Spool list: diameters, widths, weights and how many positions of each.
  • Clear height: measured to the lowest sprinkler head, light or duct; this sets the carrier count.
  • Floor space: the machine footprint plus room at the opening for a cart, a payout stand or a dolly.
  • Power: an isolated 208 volt, three phase, 15 amp circuit near the front top right of the machine.
  • Payout: decide whether you want a meter slider or spinner spools now or later.
  • Access path: doors and aisles wide enough for crated machine components and the install lifts.

With that list in hand we can recommend a configuration and quote it. For budget ranges start with the vertical storage cost and pricing guide, and for the machine family itself see the Vidir Wire Carousel page. We supply and install Vidir wire carousels nationwide, including San Diego County and the rest of Southern California, and our Utah wire spool carousel page covers projects closer to our Salt Lake City base.

Wire Spool Carousel FAQs

What is a wire spool carousel?
A wire spool carousel is a motorized vertical carousel whose carriers are enclosed wire bays. Spools sit on steel rods inside the bays, the carriers rotate inside a guarded tower, and the bay you need comes to one fixed opening at working height. The machine supplied to CES El Cajon is a Vidir W45143-0740-06.
How many spools does this wire carousel hold?
It has seven carriers with three bays each, so 21 wire bays measuring 26.25 inches wide by 32.5 inches high. Each bay takes spools up to 30 inches in diameter, and the number of spools per bay depends on spool width and how the bay is divided with rods. Each carrier is rated for 1,000 lbs.
What is the difference between W45 and W39 Vidir wire carousels?
The W45 platform has taller 32.5 inch bays for spools up to 30 inches in diameter and a 7’3″ deep footprint. The W39 platform has 26.5 inch bays for spools up to 24 inches and a 6’3″ deep footprint. Both are 8’9″ wide and come in several heights.
Why order heavy-duty 1 inch rods in every bay?
The rod carries the spool’s weight across the bay, and a 1 inch rod is stiffer than a 0.75 inch rod. Heavy-duty rods throughout suit full spools of larger conductors, and extra rods let a branch divide bays for different spool widths as the stocked wire list changes.
How much floor space does a 7-carrier W45 wire carousel use?
The machine footprint is 8’9″ wide by 7’3″ deep and it stands 12’6″ high. Plan additional clear space at the opening for the operator and for any cart, payout stand or loading dolly.
What power does it need?
This model runs on 208 volt, three phase, 15 amp power on an isolated circuit, with the connection at the front top right corner of the machine. An electrician roughs in the circuit before installation and makes the final hookup part-way through.
What does the site need to provide for installation?
Vidir’s acknowledgement for this project called for one 5,000 lb forklift with 6 ft forks and at least 12 ft of reach, one 18 to 20 ft electric scissor lift with a base no wider than 32 inches, the isolated 208V circuit and an electrician for final hookup, plus a sound concrete slab for 5/8 inch stud anchors.
Do you supply wire carousels to electrical distributors in California?
Yes. Material Handling USA supplies and installs Vidir wire carousels for electrical distributors, contractors, utilities and manufacturers nationwide, including San Diego County and Southern California. Call 800-326-4403 with your spool list and ceiling height.

Selling Wire Off Floor Stands?

Send us your spool list, with diameters, widths and full-spool weights, plus your clear ceiling height. We will size a Vidir Wire Carousel with the right platform, rod package and installation scope for your branch.

Headquartered in Salt Lake City, UT • Serving customers nationwide
Local service areas: Salt Lake City • Provo • Ogden • Park City • St. George • Logan • Lehi • Orem