Wire Spool Carousel for a Commercial Electrical Contractor: Elm Electrical, Westfield, Massachusetts

How a Western Massachusetts commercial and industrial electrical contractor put 27 bays of building wire into one 13’7″ Vidir W39 Wire Carousel, with a mixed rod package matched to its spool list.

Vidir W39 wire spool carousel with wire mesh guard and loaded wire bays in a commercial electrical contractor shop

27

Wire bays on 9 carriers

24 in

Maximum spool diameter

13’7″

Overall machine height

49

Wire bay rods, two duties

About the Project

Elm Electrical, Inc. is a commercial and industrial electrical contractor headquartered in Westfield, Massachusetts, with an Eastern Massachusetts office in Marlborough. The company works exclusively for commercial and industrial clients. Alongside the electrical contracting it was founded on, Elm offers automation and systems integration, control panel assembly, round-the-clock service and support, and electrical preventive maintenance, so one contractor can carry a facility from installation through upkeep.

Material Handling USA supplied one Vidir Wire Carousel, Model W39157-0934-06, to Elm’s Westfield facility, with freight, inside delivery and installation included. The machine is a motorized vertical carousel whose carriers are enclosed wire bays: nine carriers, 27 bays, spools up to 24 inches in diameter, in a footprint 8’9″ wide by 6’3″ deep and 13’7″ tall.

Installed Vidir Wire Carousel holding wire and cable spools behind its mesh guard in a warehouse

For an electrical contractor, wire is both the biggest consumable on every job and the hardest one to keep organized in the shop. This is our first documented Vidir wire carousel in New England and one of the real installations behind our vertical storage for electrical supply and wire distribution page, part of the wider Vidir vertical storage solutions line we supply and install nationwide.

Project Scope at a Glance

■

Vidir W39157-0934-06

A powered wire carousel 13’7″ high on an 8’9″ by 6’3″ footprint, built for spooled building wire and cable.

▲

9 carriers, 27 wire bays

Nine W39 wire-bay carriers with three bays each; every bay is 26.25″ wide by 26.5″ high.

●

Spools up to 24 in

The W39 bay takes spools up to 24 inches in diameter, the common range for commercial building wire.

🔩

Mixed rod package

18 standard-duty 0.75″ rods and 31 heavy-duty 1″ rods, so light and heavy spools each get the right support.

⚖

13,000 lb rated machine

13,000 lbs overall capacity, a 12,209 lb live load and up to 1,000 lbs on any one carrier.

🚚

Delivered and installed

Freight, inside delivery and installation by certified Vidir installers were part of the order.

Shop Static Wire Reel Racks Online

The Vidir Wire Carousel is quoted to order, not sold from the online store. For a job trailer, a service van stockroom or overflow spools in the shop, these real reel racks, a portable spool rack and spare reel rods ship from our catalog.

The Situation: Wire in a Contractor’s Shop

Electrical contractor prefab area with tagged cut wire bundles, a wire caddy and staged job carts of conduit and panels

A commercial electrical contractor’s shop is a staging area for many jobs at once. Wire comes in on spools, gets measured and cut to the lengths a crew needs, is bundled with conduit, boxes and panels for the job cart, and the partial spool goes back into stock until the next pull. A contractor that also assembles control panels and runs service calls draws even more gauges, colors and conductor types from the same stock.

The usual way to hold that wire is spools on floor-level reel stands and static reel racks along a wall. That works for a short list, but every new gauge or color adds another spool position. Partial spools get set down wherever there is room, the heaviest spools end up on the floor, and the open floor in front of the racks has to stay clear for access, which is the same floor the job carts need for staging.

A wire carousel addresses both problems in one machine: spools stack vertically inside a guarded tower, every spool keeps a fixed home, and the bay that holds the wire you need rotates down to one opening at working height. Our wire spool carousel vs. wire reel rack comparison walks through when a contractor outgrows static racks.

What Material Handling USA Supplied

Elm Electrical received one freestanding Vidir Wire Carousel, Model W39157-0934-06. It stands 13’7″ high, 8’9″ wide and 6’3″ deep. The guarding is uprights with a 2 inch wire mesh front and a corrugated sheet metal back, so the machine can sit against a wall or in an open bay with the back enclosed. Inside are nine W39 wire-bay carriers, each divided into three bays measuring 26.25 inches wide by 26.5 inches high, for 27 bays in total.

Two 1.5 HP Leeson motors drive the carousel at a fixed speed, moving carriers at up to 21 feet per minute. The operator uses forward and reverse push buttons at the front control tower, with a mushroom emergency stop and a main power disconnect. The machine runs on 208 volt, three phase, 15 amp power on an isolated circuit and is anchored to the slab with 5/8 inch HILTI KB-TZ stud anchors through 9.5 by 6 inch foot plates.

Vidir wire spool carousel with wire mesh guard, three wire bays per carrier and spools on steel rods

Nine carriers is the middle of the W39 range we have documented. Vidir builds the same 8’9″ by 6’3″ footprint at several heights, so the carrier count follows the building: a contractor with a low ceiling can stay at seven carriers, as Duro Electric in Englewood, Colorado did at 10’9″, while a high-bay shop can go to 13 carriers, as IES Residential in McKinney, Texas did at 19’3″. Elm’s 13’7″ machine adds two carriers, and six more bays, over the shortest option without needing a tall clear height.

A Mixed Rod Package Matched to the Spool List

Color-coded building wire spools on rods inside a Vidir wire carousel bay at the pick opening

In a wire carousel each spool sits on a steel rod that spans the bay, and the rod carries the spool’s weight into the carrier. Vidir offers two rod duties: 0.75 inch standard-duty rods and stiffer 1 inch heavy-duty rods. Elm’s machine was specified with both, 18 standard-duty and 31 heavy-duty rods, 49 in total.

A mixed package like this is typical of a contractor’s wire list. Smaller spools of control wire and lighter branch-circuit conductors do not need a heavy-duty rod, while full spools of larger feeder conductors do. Specifying the split up front puts the stiffer rods where the weight is and keeps the lighter bays easy to divide for narrow spools. Rods are also how a bay is divided, so more rods means more positions for small spools.

Compare that with the CES El Cajon distributor branch, which carries larger spools on a W45 machine and specified heavy-duty rods in every position. Neither approach is better in general; the right package is whatever matches the heaviest spools you keep and how finely you need the bays divided. Spare rods for either duty can be added later through our Vidir parts and service support team.

Full Product Specifications

These are the figures from Vidir’s product specification sheet for the machine supplied to Elm Electrical, cross-checked against Vidir’s drawing for the same model. They are the numbers used to confirm the machine fits the space, clears the ceiling and carries the spool weights.

Specification Value
Model W39157-0934-06
Product type Wire Carousel (vertical carousel)
Overall height 13′ 7″
Overall width 8′ 9″
Overall depth 6′ 3″
Overall weight capacity 13,000 lbs
Live load capacity 12,209 lbs
Carrier type W39 wire bay
Total carriers 9
Total wire bays 27
Wire bay dimensions 26.25″ W x 26.5″ H
Maximum spool diameter 24″
Maximum weight per carrier 1,000 lbs
Average capacity per carrier 1,000 lbs
Standard-duty wire bay rods (18) 0.75″ rods
Heavy-duty wire bay rods (31) 1″ rods
Drive system (2) 1.5 HP Leeson motors
Electrical 208V, 3-phase, 15 amp (isolated circuit)
Controls Forward/reverse push button
Drive configuration Fixed speed
Control options Mushroom E-stop, main power disconnect
Control location Front, control tower
Max. retrieval speed 21 ft per minute
Guarding Uprights, 2″ wire mesh front, corrugated sheet metal back
Foot plate dimensions 9.5″ D x 6″ W x 0.375″ H
Concrete anchors 5/8″ HILTI KB-TZ stud anchor
Finish VM White Textured
Scope of order Machine, freight, inside delivery and installation
Vidir drawing of the W39157-0934-06 wire carousel showing front, side and isometric views with overall dimensions
Vidir drawing for model W39157-0934-06: front, side and isometric views with overall width, depth and height in inches and millimeters. Rated 13,000 lbs overall and 1,000 lbs per carrier.

Installation and Site Requirements

Vidir’s order acknowledgement and set-up notice for this project list what the site needed ready before the installers arrived. An electrical contractor is well placed to handle the power side itself, but the list is the same for every buyer:

  • Power: 208 volt, three phase, 15 amp on an isolated circuit for the machine, roughed in ahead of installation.
  • Electrician mid-install: final hookup happens part-way through the installation. The outlet is at the front, top right corner of the machine when facing it.
  • Forklift: one 5,000 lb capacity forklift with 4 ft forks and at least 12 ft of high reach, for unloading the machine, moving components and assembly.
  • Scissor lift: one 18 to 20 ft electric scissor lift with a base no wider than 32 inches, so it can work close to the tower.
  • Clear install area: the space must be free of racking and stock, with room for the installers and forklift to work.
  • Slab: a sound, level concrete floor that will hold 5/8 inch HILTI KB-TZ stud anchors at each foot plate.
1

List the spools

Largest diameter, widths and full-spool weights set the platform and the split between standard and heavy-duty rods.

2

Size to the building

Clear height under sprinklers and lights picks the carrier count; the 8’9″ x 6’3″ footprint plus a clear pick zone goes on the floor plan.

3

Prepare the site

The isolated 208V circuit is roughed in, the install area is cleared and the lift equipment is lined up.

4

Deliver and install

The machine is delivered inside, erected, anchored, hooked up and tested, then staff are shown loading and rotation.

Our full pre-install checklist, including slab and access questions, is on the vertical storage installation services page.

What a Wire Carousel Gives a Contractor’s Shop

↑

27 bays in one footprint

Twenty-seven wire bays stack to 13’7″ inside an 8’9″ by 6’3″ footprint instead of a long run of floor stands.

⏱

Wire comes to the operator

The bay you call rotates to one fixed opening at up to 21 feet per minute, so nobody hunts along a wall of spools.

📦

Floor freed for staging

Spools that leave the floor give that space back to job carts, prefab benches and material for the next job.

⚖

Less lifting and bending

Spools stay on their rods inside the machine for every pull; staff work at the opening at a steady height.

🔩

Right rod for each spool

Heavy-duty rods carry the feeder spools while standard rods divide bays for lighter wire.

🔒

Guarded copper stock

Mesh front and solid sheet metal back keep wire inside a machine rather than on open racks.

Payout options for later. This order was the machine, freight and installation, with no payout accessories. Vidir’s options, such as a hanger meter slider that measures wire at the opening, wire spinner spools that pay out under even tension, and a wire loading dolly for lifting full spools to bay height, mount to the same carousel and are described on our vertical carousel accessories and options page.

How This Install Compares to Other Wire Projects

Contractors, distributors and utilities buy wire carousels for different reasons, and the right machine follows the spool list and the ceiling. These are the electrical-sector Vidir projects we have documented:

Project Customer type Machine What drove the choice
Elm Electrical, Westfield MA (this page) Commercial and industrial electrical contractor W39, 9 carriers, 27 bays, 13’7″ Mid-height shop, mixed rod package
Duro Electric, Englewood CO Electrical contractor W39, 7 carriers, 21 bays, 10’9″ Low ceiling, 24 inch spools
IES Residential, McKinney TX Residential electrical contractor W39, 13 carriers, 39 bays, 19’3″ High-volume issuing with meter slider
CES El Cajon, El Cajon CA Electrical distributor branch W45, 7 carriers, 21 bays, 12’6″ 30 inch spools, heavy-duty rods throughout
Tucson Electric Power, Tucson AZ Electric utility W45, 12 carriers, 36 bays, 21’1″ Utility reels, maximum bay count
World Electric Supply, Hialeah Gardens FL Electrical wholesaler Two tire-carousel platform machines Large cable drums, not spools

Other Northeast and Mid-Atlantic wire carousel projects include the wire spool carousel at BTECH in Rockaway, New Jersey and the wire carousel at BAE Systems in York, Pennsylvania. Every wire application we serve is mapped on the motorized wire spool carousel page, and the vertical carousel vs. traditional storage page covers the broader trade-offs.

How to Specify a Wire Carousel for Your Shop

Start with the wire, not the machine. List every spool you stock or plan to stock with its diameter, width and full weight. The largest diameter picks the platform: up to 24 inches fits W39 bays, as here; up to 30 inches needs W45. Full-spool weights decide how many heavy-duty rods you need and confirm that no carrier will exceed its 1,000 lb rating.

  • Spool list: diameters, widths, weights and how many positions of each.
  • Clear height: measured to the lowest sprinkler head, light or duct; this sets the carrier count.
  • Floor space: the machine footprint plus room at the opening for a wire cart or payout stand.
  • Power: an isolated 208 volt, three phase, 15 amp circuit near the front top right of the machine.
  • Back side: decide between a mesh or solid sheet metal back depending on whether the rear is visible or against a wall.
  • Payout: decide whether you want a meter slider or spinner spools now or later.

With that list in hand we can recommend a configuration and quote it. For budget ranges start with the vertical storage cost and pricing guide, and for the machine family itself see the Vidir Wire Carousel page. We supply and install Vidir wire carousels nationwide, including Massachusetts and the rest of New England, and our Utah wire spool carousel page covers projects closer to our Salt Lake City base.

Wire Spool Carousel FAQs

What is a wire spool carousel?
A wire spool carousel is a motorized vertical carousel whose carriers are enclosed wire bays. Spools sit on steel rods inside the bays, the carriers rotate inside a guarded tower, and the bay you need comes to one fixed opening at working height. The machine supplied to Elm Electrical is a Vidir W39157-0934-06.
How many spools does a 9-carrier W39 wire carousel hold?
It has nine carriers with three bays each, so 27 wire bays measuring 26.25 inches wide by 26.5 inches high. Each bay takes spools up to 24 inches in diameter, and the number of spools per bay depends on spool width and how the bay is divided with rods. Each carrier is rated for 1,000 lbs.
Why mix standard-duty and heavy-duty rods?
Heavy-duty 1 inch rods are stiffer and suit full spools of larger conductors; standard-duty 0.75 inch rods are enough for lighter spools. Elm’s machine has 18 standard and 31 heavy-duty rods, so each spool gets suitable support and lighter bays stay easy to divide.
How tall is a W39 wire carousel?
Vidir builds the W39 footprint at several heights. The documented examples on our site are 10’9″ with 7 carriers, 13’7″ with 9 carriers (this project) and 19’3″ with 13 carriers. Clear height under sprinklers and lights decides which fits.
How much floor space does it use?
The machine footprint is 8’9″ wide by 6’3″ deep. Plan additional clear space at the opening for the operator and for any wire cart, payout stand or loading dolly.
What power does it need?
This model runs on 208 volt, three phase, 15 amp power on an isolated circuit, with the connection at the front top right corner of the machine. The circuit is roughed in before installation and final hookup happens part-way through.
What does the site need to provide for installation?
For this project Vidir called for one 5,000 lb forklift with 4 ft forks and at least 12 ft of reach, one 18 to 20 ft electric scissor lift with a base no wider than 32 inches, a cleared install area, the isolated 208V circuit and a sound concrete slab for 5/8 inch stud anchors.
Do you supply wire carousels to electrical contractors in Massachusetts and New England?
Yes. Material Handling USA supplies and installs Vidir wire carousels for electrical contractors, distributors, utilities and manufacturers nationwide, including Massachusetts and New England. Call 800-326-4403 with your spool list and ceiling height.

Is Your Wire Still on Floor Stands?

Send us your spool list, with diameters, widths and full-spool weights, plus your clear ceiling height. We will size a Vidir Wire Carousel with the right platform, rod package and installation scope for your shop.

Headquartered in Salt Lake City, UT • Serving customers nationwide
Local service areas: Salt Lake City • Provo • Ogden • Park City • St. George • Logan • Lehi • Orem